Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers
Request Quote
All Products
Active Single-Pair Sender - Twisted Pair Format-A - Stainless - XLR mic input w phantom
Series:
Model: DS-TPS1A
- Balanced Microphone XLR Input with Phantom
- Switch-Selectable Mic Gain on Rear Panel
- Switch Selects which RJ45 Pair (A, B or C) is Fed
- Signal and Power Pair Pass-Through on RJ45 Jacks
- Remote Powering through Twisted Pair Cable
Compare
Project List
Product Info
Tech Specs
Related Products
Documents
The DS-TPS1A modules are single-pair audio sending modules compatible with RDL Format-A twisted pair products. These modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources. The D- and DS- models mount in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes. The D-TPS1A features a white front-panel laminate with gray lettering that matches RDL Decora©-style remote controls. The DS-TPS1A is constructed of stainless steel to coordinate with RDL Decora-style stainless steel remote controls in commercial/industrial installations. The AF-TPS1A is an APPFLEX series product that is compatible with various APPFLEX wall-mount, cabinet-mount and tabletop enclosures. The EM-TPS1A is a 45mm square module that fits the European Modular mounting frames and cover plates. European electrical boxes are not sufficiently deep to accommodate RJ45 jacks and plugs, therefore the EM- products connect to the twisted pair cable through a detachable terminal block. The -TPS1A modules feature an XLR microphone input. The module provides IEC 24 V phantom and accepts input signals from both dynamic and condenser microphones. The input signal is amplified using a studio-quality microphone preamplifier optimized for normal operating levels. The rear-panel GAIN switch is normally set by the installer for NORM (normal) gain. If consistently low mic levels are expected, this switch may be set to the HIGH gain position. The pre-amplified microphone source is routed to one output cable pair selected during installation using a rear-panel switch. These modules drive only one cable pair, therefore they accept signals and power from other mic-level or line-level Format-A senders. The D-, DS-, and AF- modules have a second RJ45 jack for these input cables. Installers simply connect the conductors of two cables in parallel on the EM- model terminal block. Two other single-pair senders may be chained with the DS-TPS1A, or a single two-pair sender may be connected. If three single-pair senders are connected together, each sender must feed a different pair: A, B or C. The TPS1A must be set to feed pair A if it is connected together with an RDL two-pair sender that feeds stereo audio on pairs B and C. The power pair and all three audio pairs are fed through both rear-panel RJ45 jacks. The DS-TPS1A may be powered directly from a 24 Vdc power supply using the rear-panel detachable terminal block. Local power connected to the module is also fed to all connected remote modules. The DS-TPS1A may be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED. RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity, ease of installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low distortion provide designers and installers the optimum choice in economical twisted pair products.
- Balanced Microphone XLR Input with Phantom
- Switch-Selectable Mic Gain on Rear Panel
- Switch Selects which RJ45 Pair (A, B or C) is Fed
- Signal and Power Pair Pass-Through on RJ45 Jacks
- Remote Powering through Twisted Pair Cable
- Fused Local Power Feeds all Connected Modules
- Local Power Input on Terminal Block
- Blue LED Indicates Module is Powered
- Daisy-Chain with Single-Pair or Two-Pair Senders
- Studio-Quality Precision Active Balanced Circuitry
- Operating Temperature (Maximum): 122 F
- Operating Temperature (Minimum): 32 F
- Depth: 1.89 in
- Height: 2.77 in
- Width: 2.22 in
- Product Weight: 0.40 lbs
- INPUT: 1.2 kohm Balanced with 24 Vdc phantom (IEC 1938: 1996-12)
- Input Connection: XLR
- Input Level: -45 to -65 dBu Balanced; Maximum: -40 dBu (HIGH Gain), -28 dBu (NORM Gain)
- Format-A Signal Pair Used: Switch-selectable A, B, or C
- Gain: 50 dB (NORM) or 63 dB (HIGH), Switch-selectable on rear panel
- Format-A Input: RJ45 (not applicable to EM-)
- Output: RDL TP Format-A
- Output Connection: RJ45 (Models D-, DS-, AF-); Detachable Terminal Block (Model EM-)
- Frequency Response: 100 Hz to 30 kHz (+/- 1 dB); integral low-cut filter -10 dB @ 30 Hz
- THD+N: < 0.1% (80 Hz to 20 kHz)
- Noise below +4 dBu: < -80 dB (NORM Gain), < -70 dB (HIGH Gain)
- Headroom above +4 dBu: > 18 dB
- CMRR: > 60 dB (HIGH Gain 50 Hz to 150 Hz), > 65 dB (NORM Gain 50 Hz to 150 Hz)
- Indicator: Power In
- Power Connections (2): Detachable terminal block; RJ45
- Power Requirement: 24 Vdc @ 65 mA plus connected loads
- Mounting Box Minimum Depth: 2.4 inch (Models D-, DS-, AF-); 39 mm (Model EM-)
D-TPR1A
- Active Single-Pair Receiver - Twisted Pair Format-A - XLR mic/line output
D-TPR3A
- Active Three-Pair Receiver - Twisted Pair Format-A - XLR and stereo phono outputs
D-TPS2A
- Active Two Pair Sender Twisted Pair Format-A Stereo RCA Jack Inputs
D-TPS2AM
- Active Two-Pair Sender, Twisted Pair Format-A, XLR Microphone $amp; Stereo Mini-jack In
D-TPSM2A
- 2-pair Audio Sending Module, White
DB-TPS2AM
- Active Two-Pair Sender, Twisted Pair Format-A, XLR Microphone $amp; Stereo Mini-jack In
DB-TPS3A
- DB-TPS3A
Active Three-Pair Sender - Twisted Pair Format-A - XLR microphone & stereo RCA inputs
DB-TPSM2A
- 2-pair Audio Sending Module, Black
DS-TPR1A
- Active Single-Pair Receiver - Twisted Pair Format-A - Stainless - XLR mic/line output
DS-TPR3A
- Active Three-Pair Receiver - Twisted Pair Format-A - Stainless - XLR & stereo phono out
DS-TPS2A
- Active Two-Pair Sender - Twisted Pair Format-A - Stainless - stereo phono jack inputs
DS-TPS2AM
- Active Two-Pair Sender, Twisted Pair Format-A, XLR Microphone & Stereo Mini-jack In
DS-TPSM2A
- 2-pair Audio Sending Module, Stainless Steel
FP-TP4PW
- Power Inserter - Twisted Pair - Four Sets of Outputs - Signal Loop-through
RU-BNF
- Format-A Bi-directional Network Interface
RU-BNFP
- Format-A Bi-directional Network Interface with PoE
RU-FN
- Format-A to Network Interface
RU-TP4PW
- Power Inserter - Twisted Pair - four sets of outputs - signal loop-through
RU-TPDA
- Active Distributor - Twisted Pair Format-A - RDL Format-A input to Four outputs
RU-TPS4A
- Active Sender / Distributor - Twisted Pair Format-A - Three audio inputs to Four outputs
TX-TP1PW
- Power Inserter
TX-TPS1A
- Active Single-Pair Sender, Twisted Pair Format-A
TX-TPS6A
- Passive Single-Pair Sender, Twisted Pair Format-A
Datasheet for Active Single-Pair Sender - Twisted Pair Format-A
221802 kb
- Other
Project List
Request Quote
Thank you!
Someone will be in touch with you shortly.
Contact Avidex Industries, LLC
close
Avidex Industries, LLC
8509 154th Ave NE
Suite 100
Redmond, WA 98052
USA
(425)643-0330
www.avidex.com
Contact in regards to this product:
Radio Design Labs
Model: DS-TPS1A
Request more information from a dealer near you
close
Request more information from a dealer near you